ECOFLEX SKIM COAT PUTTY
ECOFLEX SKIM COAT PUTTY is quality polymer modified product formulated for interior & exterior walls, concrete surfaces, bricks works, and fiber cement boards, block works or rendered surfaces.
Include high-quality raw materials impart required qualities such as higher whiteness level, good trowelability, excellent binding properties & crack resistance, low shrinkage finishing and supply higher flexibility with smooth finish.
APPLICATION
SURFACE PREPARATION
The surface must be clean and sound │free from loose particles, dirt, grease, wax, oil etc. │ for loose plaster and damaged areas remove the defective materials and re-plaster the area │If the climate condition is too hot, windy & too dried surfaces, dampen dry surface before application to avoid bubble formation at the application.
APPLICATION PROCEDURE
Add required amount of water to a bucket and mix with SKIM COAT PUTTY (Usually around 5-8kg water for 20kg pack). │For best results slowly add powder to water by mixing. │ keep the mixture rest for 3-5 min prior application. │ Mix thoroughly using a slow speed electric drill fitted with paddle for few minutes until desired homogeneous paste is achieved. │ Mix only sufficient compound for 1 hour working time.
Apply mixed SKIM COAT PUTTY with a hand trowel on clean and dust free surfaces. │As the surface coat hardens, trowel up the surface with a light flat toweling action, to achieve a dense smooth finish. │Nippoflex skim coat putty can be applied in a layer ranging from 1 to 3 mm in thickness. │After the first application keep it drying for 3-4 hours and apply second coat. │For the hard drying keep it for 24 hours after the second coat application. │To obtain the smooth surfaces, sanding should be required with 120 grid sandpaper. │Once the ECOFLEX has dried the final coats such as wall primers and decorative paints can be applied.
TECHNICAL DATA SHEET
COVERAGE
Generally, covers 10-15 sq.ft. per kg (200-300 sq. ft. per 20kg pack). This will depend on the nature of the wall and the thickness of the coat.
TECHNICAL INFORMATION
WATER RETENTIVELY 95%
AVERAGE SHRINKAGE 0.1%
SETTING TIME Initial set – 240 – 360 minutes
Final set – < 500 minutes
GENERAL INFORMATION
| 1st COAT
DRYING |
3 – 4 Hours (This will be depend on the climatic condition) | ||||||||||
| HARD DRYING | 24 hours (This will be depend on the climatic condition) | ||||||||||
| PACKING | 20kg | ||||||||||
| STORAGE | Store in a tightly sealed container in a cool dry place. | ||||||||||
| SHELF LIFE | 12 Months in a dry place under sealed cover
NIPPOFLEX SKIM COAT PUTTY is premium quality polymer modified product formulated for interior & exterior walls, concrete surfaces, bricks works, and fiber cement boards, block works or rendered surfaces. Include high-quality raw materials impart required qualities such as higher whiteness level, good trowelability, excellent binding properties & crack resistance, low shrinkage finishing and supply higher flexibility with smooth finish. APPLICATION SURFACE PREPARATION The surface must be clean and sound │free from loose particles, dirt, grease, wax, oil etc. │ for loose plaster and damaged areas remove the defective materials and re-plaster the area │If the climate condition is too hot, windy & too dried surfaces, dampen dry surface before application to avoid bubble formation at the application. APPLICATION PROCEDURE Add required amount of water to a bucket and mix with SKIM COAT PUTTY (Usually around 5-8kg water for 20kg pack). │For best results slowly add powder to water by mixing. │ keep the mixture rest for 3-5 min prior application. │ Mix thoroughly using a slow speed electric drill fitted with paddle for few minutes until desired homogeneous paste is achieved. │ Mix only sufficient compound for 1 hour working time. Apply mixed SKIM COAT PUTTY with a hand trowel on clean and dust free surfaces. │As the surface coat hardens, trowel up the surface with a light flat toweling action, to achieve a dense smooth finish. │Nippoflex skim coat putty can be applied in a layer ranging from 1 to 3 mm in thickness. │After the first application keep it drying for 3-4 hours and apply second coat. │For the hard drying keep it for 24 hours after the second coat application. │To obtain the smooth surfaces, sanding should be required with 120 grid sandpaper. │Once the ECOFLEX has dried the final coats such as wall primers and decorative paints can be applied. TECHNICAL DATA SHEET COVERAGE Generally, covers 10-15 sq.ft. per kg (200-300 sq. ft. per 20kg pack). This will depend on the nature of the wall and the thickness of the coat. TECHNICAL INFORMATION WATER RETENTIVELY > 95% AVERAGE SHRINKAGE < 0.1% SETTING TIME Initial set – 240 – 360 minutes Final set – < 500 minutes
GENERAL INFORMATION
|
Reviews
There are no reviews yet.